Course Title: Select wiring systems and cables for low voltage general electrical installations
Part B: Course Detail
Teaching Period: Term1 2017
Course Code: EEET7125C
Course Title: Select wiring systems and cables for low voltage general electrical installations
School: 174T School of VE Engineering, Health & Science
Campus: City Campus
Program: C3296 - Certificate III in Electrotechnology Electrician
Course Contact: Program Manager
Course Contact Phone: +61 3 9925 4468
Course Contact Email: vocengineering@rmit.edu.au
Name and Contact Details of All Other Relevant Staff
Nominal Hours: 80
Regardless of the mode of delivery, represent a guide to the relative teaching time and student effort required to successfully achieve a particular competency/module. This may include not only scheduled classes or workplace visits but also the amount of effort required to undertake, evaluate and complete all assessment requirements, including any non-classroom activities.
Pre-requisites and Co-requisites
UEENEEE101A; UEENEEE102A; UEENEEE104A; UEENEEE105A; UEENEEE107A; UEENEEG006A; UEENEEG033A; UEENEEG063A; UEENEEG101A; UEENEEG102A; UEENEEG106A
Course Description
This unit covers selecting wiring systems and cables for electrical installations operating at voltages up to 1,000V a.c. or 1,500 V d.c. It encompass knowledge and application of wiring systems and cable types, selecting wiring system compatible with the installation conditions, selecting cables that comply with required current-carrying capacity and voltage drop and earth fault-loop impedance limitations, coordination between protective devices and conductors and documenting selection decisions.
Note: EEET7147C (Mount Isa Institute of TAFE) offering is only applicable for program C4315.
National Codes, Titles, Elements and Performance Criteria
National Element Code & Title: |
UEENEEG107A Select wiring systems and cables for low voltage general electrical installations |
Element: |
1. Prepare to select wiring systems and cables for general electrical installations |
Performance Criteria: |
1.1 The extent and nature of the electrical installation is determined from job specifications. 1.2 Safety and other regulatory requirements to which the electrical installation shall comply area are identified, obtained and understood. 1.3 Cable routes, the route lengths of cables and the conditions in which the wiring system is to operate is determined from job specifications or from consultation with appropriate persons. |
Element: |
2. Select wiring systems and cables for general electrical installations |
Performance Criteria: |
2.1 Wiring systems are selected for suitability for the environments in which they are to operate. 2.2 Cable conductor sizes are selected to meet current-carrying capacity requirements and voltage-drop and earth fault-loop impedance limitations. 2.3 Circuit protective devices are selected to meet requirement for co-ordination with conductor current-carrying capacity. 2.4 Earthing system components are selected to meet requirements of an MEN system. 2.5 Evidence is obtained that electrical equipment selected complies with safety requirements. |
Element: |
3. Document electrical installation |
Performance Criteria: |
3.1 Evidence is obtained from manufacturers/suppliers that electrical equipment selected complies with safety requirements. 3.2 Reasons for selections made, including calculations, are documented in accordance with established procedures. 3.3 Electrical installation arrangement and specifications for all selected items are documented in accordance with established procedures and forwarded to appropriate person(s). |
Learning Outcomes
Refer to Elements
Details of Learning Activities
Students will be involved in the following learning activities to meet requirements for this competency:
- Face to Face classes
- Simulated Workplace Learning
- Online learning via blackboard
- Other forms of structured teaching and learning
Students will be observed and assessed through their planned activities throughout the duration of the course.
Teaching Schedule
Please refer to your class timetable
Learning Resources
Prescribed Texts
References
Other Resources
Students will be able to access course information and learning materials through myRMIT and may be provided with additional materials in class. Lists of relevant reference books, resources in the library and accessible Internet sites will be provided where possible. During the course, you will be directed to websites to enhance your knowledge and understanding of difficult concepts.
Overview of Assessment
Students must pass each of the following assessment tasks to demonstrate competent.
Assessments | |
Task 1 |
Workbook |
Task 2 |
Practical – 1 - 4 |
Task 3 |
Assessment MD & Cable Selection |
Task 4 |
Theory Exam |
These tasks assesses the following Course Learning Outcomes (CLOs):
Assessment Mapping Matrix
Elements/Performance Criteria Covered |
Task 1 |
Task 2 |
Task 3 |
Task 4 |
1.1 |
X |
X |
X |
X |
1.2 |
X |
X |
X |
X |
1.3 |
X |
X |
X |
X |
2.1 |
X |
X |
X |
X |
2.2 |
X |
X |
X |
X |
2.3 |
X |
X |
X |
X |
2.4 |
X |
X |
X |
X |
2.5 |
X |
X |
X |
X |
3.1 |
X |
X |
X |
X |
3.2 |
X |
X |
X |
X |
3.3 |
X |
X |
X |
X |
To be deemed competent you must demonstrate an understanding of all aspects required of the competency.
Assessment methods have been designed to measure your achievement of each competency in a flexible manner over multiple tasks.
Assessment Tasks
Students must pass each of the following assessment tasks to demonstrate competent.
Assessment | |
Task 1 |
Practical: Switchboards |
Task 2 |
Assignment: MD/cable/circuits |
Task 3 |
Theory Exam |
Assessment Matrix
Please refer to the above matrix.
All assessment tasks must be successfully completed
Other Information
Credit Transfer and/or Recognition of Prior Learning (RPL):
You may be eligible for credit towards courses in your program if you have already met the learning/competency outcomes through previous learning and/or industry experience. To be eligible for credit towards a course, you must demonstrate that you have already completed learning and/or gained industry experience that is:
• Relevant
• Current
• Satisfies the learning/competency outcomes of the course
Please refer to http://www.rmit.edu.au/students/enrolment/credit to find more information about credit transfer and RPL.
Study and Learning Support:
Study and Learning Centre (SLC) provides free learning and academic development advice to you. Services offered by SLC to support your numeracy and literacy skills are:
• Assignment writing, thesis writing and study skills advice
• Maths and science developmental support and advice
• English language development
Please refer to http://www.rmit.edu.au/studyandlearningcentre to find more information about Study and Learning Support.
Disability Liaison Unit:
If you are suffering from long-term medical condition or disability, you should contact Disability Liaison Unit to seek advice and support to complete your studies.
Please refer to http://www.rmit.edu.au/disability to find more information about services offered by Disability Liaison Unit.
Late Submission:
If you require an Extension of Submittable Work (assignments, reports or project work etc.) for seven calendar days or less (from the original due date) and have valid reasons, you must complete an Application for Extension of Submittable Work (7 Calendar Days or less) form and lodge it with the Senior Educator/ Program Manager.
The application must be lodged no later than one working day before the official due date. You will be notified within no more than two working days of the date of lodgement as to whether the extension has been granted.
If you seek an Extension of Submittable Work for more than seven calendar days (from the original due date), you must lodge an Application for Special Consideration form under the provisions of the Special Consideration Policy, preferably prior to, but no later than two working days after the official due date.
Submittable Work (assignments, reports or project work etc.) submitted late without approval of an extension will not be accepted or marked.
Special Consideration:
Please refer to http://www.rmit.edu.au/students/specialconsideration to find more information about special consideration.
Plagiarism:
Plagiarism is a form of cheating and it is very serious academic offence that may lead to expulsion from the university.
Please refer to http://www.rmit.edu.au/academicintegrity to find more information about plagiarism.
Email Communication:
All email communications will be sent to your RMIT email address and you must regularly check your RMIT emails.
Course Overview: Access Course Overview